Products
Pdlux is one of Microwave Sensor Module, PIR Motion Sensor, Microwave Motion Lamps Manufacturers and Suppliers in China. We are committed to improving the quality of our products and optimizing after-sales services. Over the years, we have developed customers all over the world and won unanimous praise.
IP44 Waterproof Infrared Sensor
PDLUX PD-PIR109-Z
Read More›
IP44 Waterproof Infrared Sensor is an advanced digitally controlled infrared pyroelectric intelligent sensor product. It uses the MCU to accurately calculate the switch information, and accurately controls the relay to be turned on at the zero point of the sine wave, so that each load is turned on. At the zero point of the sine wave, the inrush current problem caused by the conventional control mode when the sine wave high voltage is turned on is avoided, especially the large current damage relay generated by the large-capacity capacitor under the impact of the high voltage under the load.
24GHz Automatic Door Microwave Sensor
PDLUX PD-DS1015
Read More›
Using the original Omron relay which has an ultra small measurement and low power consumption. 24GHz Automatic Door Microwave Sensor has a small internal resistance to make it insensitive to temperature. The reliability is much higher than the common photoelectric-output ones. It’s suitable for different kinds of auto-door-controller also can applicated as a human detector for alarm systems.. Besides, the sensing function can be customized. The sensor has the best cost performance during such kind of products.
Remote Microwave Sensor
PDLUX PD-MV1028
Read More›
Remote Microwave Sensor is mainly for the adjustment of the delay time from the moment the signal detected and light auto-on till the light auto-off. You can define the delay time to your practical need. But you’d better lower the delay time for the sake of energy saving, since the microwave sensor has the function of continuous sensing, that is, any movement detected before the delay time elapses will re-start the timer and the light will keep on only if there is human in the detection range.
High-power Microwave Inductor
PDLUX PD-MV1009
Read More›
When use High-power Microwave Inductor, please adjust the sensitivity to an appropriate position you need, please do not adjust the sensitivity to maximum, to avoid the product does not work normally caused by wrong motion.Because the sensitivity is too high easily detect the wrong motion by wind blowing leaves & curtains, small animals, and the wrong motion by interference of power grid & electrical equipment. All those lead the product does not work normally !
Miniature Microwave Sensor
PDLUX PD-MV1019
Read More›
Miniature Microwave Sensor is widely applied in the passageway, washroom, elevator, household or other public areas for security protection or energy saving. Miniature Microwave Sensor applies for several technical patents and is the perfect choice for your intelligent living.
RED Certified Microwave Sensors
PDLUX PD-MV1012-Z
Read More›
RED Certified Microwave Sensors uses the MCU to accurately calculate the switch information, and accurately controls the relay to be turned on at the zero point of the sine wave, so that each load is turned on. At the zero point of the sine wave, the inrush current problem caused by the conventional control mode when the sine wave high voltage is turned on is avoided, especially the large current damage relay generated by the large-capacity capacitor under the impact of the high voltage under the load.
Zero Crossing Technology Microwave Sensor
PDLUX PD-MV1005-Z
Read More›
Zero Crossing Technology Microwave Sensor is a moving object sensor that can detect range of 360°and ifs working frequency is 5.8G.The advantage of this product is stable working state (stable working temperature: -15°C~+70°C), PD-MV1005-Z adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe and performs better than infrared sensor.
Wall 180° Detects Microwave Sensors
PDLUX PD-MV1027-Z
Read More›
Wall 180° Detects Microwave Sensors is mainly for the adjustment of the delay time from the moment the signal detected and light auto-on till the light auto-off. You can define the delay time to your practical need. But you'd better lower the delay time for the sake of energy saving, since the microwave sensor has the function of continuous sensing, that is, any movement detected before the delay time elapses will re-start the timer and the light will keep on only if there is human in the detection range.
